Factory-direct supply · GB standard · Export packingISO 9001 / ISO 14001 / ISO 45001
Home/Products/Two-Fabric One-Membrane Composite Geomembrane

Two-Fabric One-Membrane Composite Geomembrane

The heavier 2F1M composite build-up for canals, reservoirs and slopes where puncture protection and tensile strength are both required.

600g/1.5mm/600g; 500g/1.0mm/500g; 400g/0.75mm/400gVirgin HDPE, 0.5-2.0 mmBatch test reportExport packing
Two-Fabric One-Membrane Composite Geomembrane produced by Hengyang

Representative photo of Two-Fabric One-Membrane Composite Geomembrane; final surface, width and roll length are confirmed at order.

Specification

Standard range

StructureTwo fabric / one membrane (2F1M)
Common build-ups600g/1.5mm/600g; 500g/1.0mm/500g; 400g/0.75mm/400g
MembraneVirgin HDPE, 0.5-2.0 mm
Tensile strength≥ 20 kN/m at 600g/1.5mm/600g
Peel strength≥ 60 N/cm, factory bonded
StandardGB/T 17642-2008

Typical production ranges for Two-Fabric One-Membrane Composite Geomembrane; project values are confirmed against the drawing and test report before shipment.

Request data sheet & quote

Classification and applications

Reservoir and canal lining with 600g/1.5mm/600g typical build-up. The material package around Two-Fabric One-Membrane Composite Geomembrane — cushion geotextile, drainage, anchoring and welding — is selected with the same drawing.

Best fit for Two-Fabric One-Membrane Composite Geomembrane

  • Reservoir slopes with coarse subgrade
  • Canals with construction traffic
  • Ponds needing both faces protected

What we need to quote

  • Thickness or mass per unit area, width and quantity
  • Project type, design head and chemical exposure
  • Standard or specification clauses, if any
  • Delivery port and required date
Comparison

How Two-Fabric One-Membrane Composite Geomembrane compares

2F1M protects both faces and gives the highest composite tensile. 1F1M is lighter and cheaper where only one face needs protection or the liner is covered by prepared soil.

Compare with my specification

Reference configuration

Jining mining subsidence reservoir — 2F1M composite geomembrane + eco bag slope protection. Reference configuration for Two-Fabric One-Membrane Composite Geomembrane, not a delivered project record.

Read before specifying

Typical build-ups using this material

Reference configurations, not delivered project records.

Material behaviour

Why this material is selected

  • Two fabric layers around one HDPE membrane, commonly 600g/1.5mm/600g.
  • Tensile strength ≥ 20 kN/m and peel strength ≥ 60 N/cm.
  • Balances puncture protection and sealing for reservoirs, caps and channels.
Application fit

Where Two-Fabric One-Membrane Composite Geomembrane fits

The heavier 2F1M composite build-up for canals, reservoirs and slopes where puncture protection and tensile strength are both required.

Final thickness, width and surface are confirmed against the drawing, design head and chemical exposure.

Installation

Installation steps and checks

  1. Confirm the fabric weight, membrane thickness and total roll weight
  2. Lay with the membrane edge exposed for double-track welding
  3. Keep fabric edges clean and dry before welding
  4. Stitch or overlap fabric edges as specified, then protect the surface

Welding parameters and seam records for Two-Fabric One-Membrane Composite Geomembrane are supplied with the shipment; for the first production welds, an engineer can attend site.

Questions buyers ask about Two-Fabric One-Membrane Composite Geomembrane

When is 2F1M preferred over 1F1M?

Use 2F1M when both faces need protection, when the subgrade is coarse, or when the liner must carry construction traffic. Use 1F1M for lighter, well-prepared bases.

When is composite geomembrane better than a plain liner?

Composite membrane protects the liner during installation and service, and adds filtration. It is widely used for canals, reservoirs and ponds where site conditions are less controlled.

What does 600g/1.5mm/600g mean?

It describes 600 g/m² geotextile on each face of a 1.5 mm geomembrane. Heavier fabric gives more puncture protection and tensile strength.

Can it be welded?

The membrane edge is exposed for double-track thermal welding; fabric edges are stitched or overlapped according to the installation method statement.

Related

Related products and engineering packages

Other products in the composite range, plus the eight material systems used around Two-Fabric One-Membrane Composite Geomembrane.

Composite GeomembraneComposite Geomembrane

Composite Geomembrane

canals, reservoirs and ponds where lining and filtration are combined

One-Fabric One-Membrane Composite GeomembraneComposite Geomembrane

One-Fabric One-Membrane Composite Geomembrane

channel lining and ponds where a lighter composite is specified

Waterproof Composite GeotextileComposite Geomembrane

Waterproof Composite Geotextile

basement and roof waterproofing with a bonded membrane core

Anti-Seepage Composite GeotextileComposite Geomembrane

Anti-Seepage Composite Geotextile

fish ponds, reservoirs and small dams needing a flexible seepage barrier

All eight material systems

Quote builder

Build a quote request in 30 seconds

Fill what you know. The button creates a structured email in your mail app; nothing is stored on this website.

Contact sales

Need Two-Fabric One-Membrane Composite Geomembrane for a project?

Send the specification values, area, head and delivery port for Two-Fabric One-Membrane Composite Geomembrane; we will confirm the standard and reply with a material schedule.

Call +86 400-150-1689 Send project details
Call sales WhatsApp Get quote Products