Factory-direct supply · GB standard · Export packingISO 9001 / ISO 14001 / ISO 45001
Home/Products/One-Fabric One-Membrane Composite Geomembrane

One-Fabric One-Membrane Composite Geomembrane

A lighter 1F1M composite for channels and ponds where one protected face is sufficient and material cost matters.

400g/1.0mm, 300g/0.75mm, 500g/1.5mmHDPE or LLDPE, 0.5-1.5 mmBatch test reportExport packing
One-Fabric One-Membrane Composite Geomembrane produced by Hengyang

Representative photo of One-Fabric One-Membrane Composite Geomembrane; final surface, width and roll length are confirmed at order.

Specification

Standard range

StructureOne fabric / one membrane (1F1M)
Common build-ups400g/1.0mm, 300g/0.75mm, 500g/1.5mm
MembraneHDPE or LLDPE, 0.5-1.5 mm
Tensile strength≥ 12 kN/m at 400g/1.0mm
Width4-6 m
StandardGB/T 17642-2008

Typical production ranges for One-Fabric One-Membrane Composite Geomembrane; project values are confirmed against the drawing and test report before shipment.

Request data sheet & quote

Classification and applications

Channel lining and ponds where a lighter composite is specified. The material package around One-Fabric One-Membrane Composite Geomembrane — cushion geotextile, drainage, anchoring and welding — is selected with the same drawing.

Best fit for One-Fabric One-Membrane Composite Geomembrane

  • Small canals and ditches
  • Ponds with prepared sand base
  • Temporary or staged water storage

What we need to quote

  • Thickness or mass per unit area, width and quantity
  • Project type, design head and chemical exposure
  • Standard or specification clauses, if any
  • Delivery port and required date
Comparison

How One-Fabric One-Membrane Composite Geomembrane compares

1F1M saves weight and cost but leaves one membrane face exposed to the subgrade. If the base is coarse or the liner will be trafficked, use 2F1M or add a separate cushion.

Compare with my specification

Reference configuration

Yellow River Delta aquaculture pond renovation — 1.0 mm HDPE liner, 8 m width, 12 ponds. Reference configuration for One-Fabric One-Membrane Composite Geomembrane, not a delivered project record.

Read before specifying

Typical build-ups using this material

Reference configurations, not delivered project records.

Material behaviour

Why this material is selected

  • One fabric layer bonded to one HDPE or LLDPE membrane, commonly 400g/1.0mm.
  • Tensile strength ≥ 12 kN/m at 400g/1.0mm.
  • A lower-cost build for channels, fish ponds and shallow basins.
Application fit

Where One-Fabric One-Membrane Composite Geomembrane fits

A lighter 1F1M composite for channels and ponds where one protected face is sufficient and material cost matters.

Final thickness, width and surface are confirmed against the drawing, design head and chemical exposure.

Installation

Installation steps and checks

  1. Confirm the fabric weight, membrane thickness and total roll weight
  2. Lay with the membrane edge exposed for double-track welding
  3. Keep fabric edges clean and dry before welding
  4. Stitch or overlap fabric edges as specified, then protect the surface

Welding parameters and seam records for One-Fabric One-Membrane Composite Geomembrane are supplied with the shipment; for the first production welds, an engineer can attend site.

Questions buyers ask about One-Fabric One-Membrane Composite Geomembrane

Which face should the fabric be on?

The fabric is normally placed against the subgrade or the side needing protection. Confirm the orientation with the panel layout and the installation method statement.

When is composite geomembrane better than a plain liner?

Composite membrane protects the liner during installation and service, and adds filtration. It is widely used for canals, reservoirs and ponds where site conditions are less controlled.

What does 600g/1.5mm/600g mean?

It describes 600 g/m² geotextile on each face of a 1.5 mm geomembrane. Heavier fabric gives more puncture protection and tensile strength.

Can it be welded?

The membrane edge is exposed for double-track thermal welding; fabric edges are stitched or overlapped according to the installation method statement.

Related

Related products and engineering packages

Other products in the composite range, plus the eight material systems used around One-Fabric One-Membrane Composite Geomembrane.

Composite GeomembraneComposite Geomembrane

Composite Geomembrane

canals, reservoirs and ponds where lining and filtration are combined

Two-Fabric One-Membrane Composite GeomembraneComposite Geomembrane

Two-Fabric One-Membrane Composite Geomembrane

reservoir and canal lining with 600g/1.5mm/600g typical build-up

Waterproof Composite GeotextileComposite Geomembrane

Waterproof Composite Geotextile

basement and roof waterproofing with a bonded membrane core

Anti-Seepage Composite GeotextileComposite Geomembrane

Anti-Seepage Composite Geotextile

fish ponds, reservoirs and small dams needing a flexible seepage barrier

All eight material systems

Quote builder

Build a quote request in 30 seconds

Fill what you know. The button creates a structured email in your mail app; nothing is stored on this website.

Contact sales

Need One-Fabric One-Membrane Composite Geomembrane for a project?

Send the specification values, area, head and delivery port for One-Fabric One-Membrane Composite Geomembrane; we will confirm the standard and reply with a material schedule.

Call +86 400-150-1689 Send project details
Call sales WhatsApp Get quote Products