Factory-direct supply · GB standard · Export packingISO 9001 / ISO 14001 / ISO 45001
Home/FAQ

Geomembrane and geosynthetic questions, grouped by topic

Commercial and technical questions from overseas buyers, arranged the same way as the Chinese FAQ page — materials, selection, price, installation, quality, supply and other questions. If your question is not here, send it with the project details.

7 topic groups32 answersProject-specific reply in one working day
FAQ group

Understanding materials

What is the difference between a geomembrane and a geotextile?

A geomembrane is impermeable and controls seepage. A geotextile is permeable and provides filtration, separation, drainage and protection. Most containment systems use both: the membrane blocks water and the geotextile protects and drains.

Which standards do you manufacture to?

Geomembrane to GB/T 17643-2011, composite geomembrane to GB/T 17642-2008, geotextile to GB/T 17638-2017, waterproof board to GB/T 18173.1. Project-specific standards can be quoted.

Can you manufacture to ASTM or EN standards?

We produce to GB/T standards as standard. For ASTM or EN clauses, send the specification and we will confirm which values can be met and which need a custom run.

Can LDPE be used as a landfill primary liner?

No. LDPE is more flexible but has lower tensile strength, puncture resistance and stress-crack resistance than HDPE. For a landfill primary liner, specify HDPE to GB/T 17643; LDPE is for small ponds, temporary covers and detailing.

What is the difference between 1F1M and 2F1M?

1F1M is one geotextile fabric bonded to one geomembrane; 2F1M is two fabric layers around one membrane. 2F1M gives more cushioning and puncture protection, at a higher mass and cost.

When should I use GCL instead of a composite geomembrane?

GCL is useful where bentonite self-healing, low permeability and simple seaming are advantages, such as caps, basement walls and shafts. A composite geomembrane is usually preferred where higher tensile strength and welded membrane seams are required.

FAQ group

Selection and thickness

How do I choose geomembrane thickness?

Start with the design head, then add allowances for subgrade, construction traffic and service life. Landfill base liners are commonly 1.5 mm, hazardous waste 2.0 mm, reservoirs 1.0-1.5 mm and small ponds 0.5-1.0 mm. The design drawing governs.

Should I specify smooth or textured geomembrane?

Use smooth liner on flat floors and tank bases where welding access is good. Use textured or studded liner on slopes steeper than about 1:3, where soil cover or friction stability governs.

What thickness is common for a landfill liner?

1.5 mm HDPE is common for municipal solid waste landfill base and side slopes; 1.0-1.5 mm is used for reservoirs and ponds; 0.5-1.0 mm for temporary or low-head containment. The design head, subgrade and puncture risk govern the final value.

How long does a geomembrane last?

Service life depends on resin, thickness, UV exposure, temperature and mechanical protection. A covered HDPE liner in a normal containment application is expected to remain serviceable for decades; exposed sheet needs UV stabilisation and should not be left uncovered longer than necessary.

Do you provide product data sheets and declarations?

Yes. Each product has a data sheet with the standard, thickness or mass range, typical values and applications. Declarations of conformity and batch test reports are issued with the shipment.

Can you slit rolls to a specific width?

Yes. Rolls can be slit to the width required by the panel layout, within the production width. Custom slit widths carry a setup cost and a minimum run.

FAQ group

Price and quotation

What is the minimum order?

Small trial orders are accepted for standard specifications. Custom thickness, width and colour usually start at one production run, typically 1,000-3,000 m².

Can you quote from a drawing or bill of quantities?

Yes. Send the drawing, specification clauses and bill of quantities. We will map each item to a standard product, flag any non-standard value and return a material schedule.

FAQ group

Installation and welding

Do you provide installation guidance?

Yes. We provide welding parameters, seam testing guidance and installation checklists, and can arrange an engineer to attend the site for critical projects.

How are geomembrane seams tested?

Every production seam is air-tested (or vacuum-tested where specified). T-joints and pipe penetrations are reinforced with extrusion welding or a patch, and the results are recorded by seam number.

Do you supply installation crews?

We supply material, welding parameters, seam-testing guidance and installation checklists. For critical first welds, an engineer can attend site. Full installation crews are arranged by the buyer or its contractor.

Can you attend the first weld?

Yes for critical projects. Travel and site access are arranged with the buyer; remote review of trial-weld records is also possible.

Can seams be welded in rain or wind?

No. Rain, standing water, dust and strong wind degrade seam quality. Stop welding, cover the work area and dry the sheet before trial welding again. The trial-weld parameters must match the day's temperature and humidity.

What is the minimum seam overlap?

For double-track thermal welding, the usual overlap is 80-100 mm, with the exact value set by the welder and trial weld. Always follow the project specification and the welding equipment manufacturer's data.

How is a failed seam repaired?

A failed seam is opened, cleaned and dried, then repaired with a new weld, a patch or extrusion welding as specified. The repair is retested and recorded against the original seam number.

FAQ group

Quality and inspection

Can you arrange third-party inspection?

Yes. The buyer or its nominated inspection company can witness production, sampling and testing. We will prepare the access, samples and documents required for the inspection.

What happens if a batch fails inspection?

The batch is not released. We re-test the retained sample, review the production record and replace the affected rolls. Third-party inspection results are handled through the same quality-claim process.

What documents are supplied with a shipment?

Commercial invoice and packing list, mill test certificate and batch test report, product data sheet, welding parameters and loading photos. Certification packs can be added for tender or customs purposes.

FAQ group

Supply and delivery

Can you send samples before an order?

Yes. Standard samples of geomembrane, geotextile, GCL and drainage net can be couriered free of charge; the buyer covers freight on larger sample sets.

Where is the factory?

The factory is in Lingcheng Economic Development Zone, Dezhou, Shandong, about 1.5 hours by high-speed rail from Jinan. Visits and sample collection can be arranged on weekdays.

How do you pack for export?

Rolls are labelled with product, thickness, batch and length, then palletised or loaded in containers with UV cover and desiccant where needed.

What payment terms do you accept?

Typically 30% deposit and balance before shipment for a first order; terms can be discussed for repeat business.

Do you supply geogrid, geocell and drainage board as well?

Yes. The wider range includes geogrid, geocell, drainage board, soft drainage pipe and other geosynthetics. Send the schedule and we will confirm which items are standard and which are custom.

FAQ group

Other questions

Can you provide project references?

We can discuss comparable references and test records after commercial qualification and an NDA. Reference profiles on this site are configurations, not claims of delivered projects.

How can I verify your certificates?

Check the legal entity, certificate number and validity period against the original, then verify with the issuing body. Stamped scans and a certificate pack can be requested from sales.

Question not answered here?

Send the drawing, product and site condition. A technical reply will follow within one working day.

Call +86 400-150-1689 Send project details
Call sales WhatsApp Get quote Products